HD-RXU-4KZ-101-E

The HD‑RXU‑4KZ‑101‑E is a DM® Essentials 4K60 4:4:4 receiver designed to interoperate with a DM Essentials HD‑TXU‑4KZ Series transmitter for the extension of HDMI® and USB 2.0 signals. This is useful in applications where an AV source is located remotely from its destination, such as a display, projector, or codec solution. A CAT5e or higher twisted pair cable (Crestron DM‑CBL‑8G or DM‑CBL‑ULTRA sold separately) must be used to connect the HD‑RXU‑4KZ‑101‑E to the DM Essentials transmitter.1

Interoperability with a DM Essentials HD-TXU-4KZ Series Transmitter

For interoperability between the HD‑RXU‑4KZ‑101‑E and an HD‑TXU‑4KZ Series transmitter, the DM Essentials input port of the HD‑RXU‑4KZ‑101‑E must be connected to the DM Essentials output port of the HD‑TXU‑4KZ Series transmitter.

NOTE: USB 2.0 data extension is not supported if the HD-RXU-4KZ-101-E is paired with a DM Essentials transmitter other than an HD-TXU-4KZ Series transmitter or paired with a DMPS Essentials HD-PS Series switcher.

4K60 4:4:4 and HDR Support

The HD-RXU-4KZ-101-E supports video resolutions up to 4K60 with 4:4:4 color sampling. HDR10, HDR10+, and Dolby Vision® video formats are also supported.2

USB 2.0 Data Extension

Two USB 2.0 host ports are provided on the HD-RXU-4KZ-101-E, enabling connection to a wide variety of supported USB 2.0 peripheral devices.3

Ethernet Pass-Through Capability

The HD‑RXU‑4KZ‑101-E is equipped with a 100/1000 Mbps LAN port that receives an Ethernet signal transmitted over the DM Essentials connection from the transmitting endpoint. The LAN port of one endpoint can be connected to an Ethernet network, while the LAN port of the other endpoint can be connected directly to an Ethernet-enabled device such as a PC.

Compact, Surface-Mountable Design

Compact in design, the HD-RXU-4KZ-101-E can be mounted onto a flat surface such as a wall behind a flat-panel display or a ceiling above a projector. It can also be attached to a single rack rail in the back of an equipment cabinet. The HD-RXU-4KZ-101-E can receive power from the included power pack or from the remote DM Essentials transmitter.4

Key Features

• DM® Essentials receiver functionality designed to interoperate with a DM Essentials HD-TXU-4KZ Series transmitter

• Point-to-point extension of an HDMI® AV signal, USB 2.0 data signals, and Ethernet signal over a CAT5e or higher cable

• DM Essentials transmission distance up to 130 ft (40 m) for UHD and 4K signals or up to 230 ft (70 m) for 1080p, WUXGA, and 2K signals

• 4K60 4:4:4 capability

• HDR10, HDR10+, and Dolby Vision® video formats

• Ethernet pass-through capability

• Compliance with HDCP 2.3

• CEC (Consumer Electronics Control) pass-through capability

• EDID pass-through capability

• Compact, surface-mountable design

• Power from 24VDC power pack (included) or from remote DM Essentials transmitter

1. For DM Essentials connections, use Crestron DM-CBL-8G, Crestron DM-CBL-ULTRA, or third-party CAT5e or higher cable. To safeguard against unpredictable environmental electrical noise that may impact performance at resolutions above 1080p, shielded cable and connectors are recommended for all applications and are required when bundling multiple cables in a wire run. Cables are sold separately.

2. 4K60 4:4:4 performance and HDR support require the use of HDMI cables and couplers with a minimum TMDS bandwidth of 18 Gbps. If 4K60 4:2:0 or 4K30 4:4:4 performance is acceptable, cables and couplers with a minimum bandwidth of 10.2 Gbps may be used. Bandwidth loss is cumulative; therefore, performance may be reduced when inserting multiple cables and couplers inline.

3. The HD-RXU-4KZ-101-E is engineered to deliver maximum compatibility with the widest possible range of USB devices. Crestron does not guarantee that all USB devices are compatible with the HD-RXU-4KZ-101-E.

4. When a surface-mountable DM Essentials receiver is paired with a surface-mountable DM Essentials transmitter, either the power pack included with the receiver or the transmitter can be used to power both devices. A power pack must not be connected to both devices simultaneously. When a surface-mountable DM Essentials receiver is paired with a wall plate DM Essentials transmitter, the power pack included with the receiver must be used to power both devices.

5. The HDMI output requires an appropriate adapter or interface cable to accommodate a DVI signal. CBL-HD-DVI interface cables are sold separately.